Deformable and High Adhesion Strength Tile Adhesive C2TE S1
Description
High performance cementitious S1 class deformable tile adhesive, with extended open time and reduced slip, for ceramic tiles and stones.
Fields of Application
● Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete.
● Bonding of tiles on existing ceramic tile, granite.
● Bonding of tiles on painted walls and gypsum.
● Bonding of ceramic tiles in swimming pools, basins and any other wet places.
● Bonding of tiles on terraces and balconies.
● Bonding of tiles on places where sudden temperature changes occur like cold storage depots and underfloor heating systems.
● Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools.
● Approved for use with plywood.
●Perfect adherence.
● Highly deformable thanks to its S1 classification, it is resistant to temperature changes.
● Can be applied on vertical surfaces even for bonding of heavy tiles, without sagging.
● Extended open time.
● Easily trowelable.
● Substrates must be sound, free from oil, grease and sufficiently dry. Cementitious substrates must be cured.
● Cracked plaster mortar and cement residues must be scraped off the surface.
● The porous surfaces should be wetted and must be left to dry before application.
● The surface should be primed with (Primer) depending on the absorbency of the rate before application.
● Wipe the back sides of tiles with water if dusty.
● Pour ProFlex into the advised amount of clean water slowly and mix to obtain a homogeneous paste, free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application.
● Allow the mortar to stand for 5-10 minutes to mature. After 1-2 minutes of remixing, the paste is ready for application.
● Consumption is 3-5 kg/m20
● Consume the prepared mortar within 2-3 hours.
● Spread the mortar onto the substrate with a notched trowel, of which notch size is appropriate to the tile dimension. To obtain a good adhesion, first apply a thin coat of ProFlex with the flat side of the trowel, then notch with the toothed side of the trowel.
● In case of applications of large tiles (greater than 40×40 cm), on existing tiles or in areas which are subject to frost or heavy traffic, ProFlex should also be applied on the back of tiles (combined method).
● Open time is 30 minutes. Install the tiles within this period of time with firm pressure. Unfavorable climatic conditions (high temperature, low humidity, wind, etc.) can reduce this time to just a few minutes. If this period is exceeded, scratch and discard the mortar.
● Clean tools and hands with water, and surfaces with a damp cloth.
● It is recommended to use protective gloves and goggles.
● Dispose mortars of which the pot life is expired.
● Tiles installed with ProFlex must not be subject to water for at least 24 hours and must be protected from frost and strong sunlight for at least 5-7 days after installation.
● Time required for grouting on walls is 8 hours and on floors is 24 hours.
● Floors can be opened to light foot traffic after 24 hours.
● It should not be applied in rainy weather and the applied surface should be protected from rain in 24 hours.
● Application temperature should be between °5+C and °35+C.
● Since it contains cement, it irritates the eyes, respiratory system and skin.
● The consumption values in the table refers to an average consumption amount. It may vary depending on the application conditions and surface properties.Storage
● Product storage conditions should be between °5+C and °35+C.
● Store in dry medium.
● Do not stack more than 10 bags on top of each other.
Packaging
● 20 kg multi-ply paper bags.
● 25 kg multi-ply paper bags.
Certificates of Quality
Class C2TE, S1
C: Cementitious
2: Improved
T: Reduce slip
E: Extended Open Time
S1: Deformable
TESTIMONIALS
What Our Cutomers are Saying About us
We Invite Individuals
To Submit CV's
We are actively seeking to expand our team and are excited about the opportunity to welcome new talent. We aim to enhance our workforce with diverse perspectives and skills.
From research and development to manufacturing and customer service, we uphold the highest standards to ensure that our products not only meet but exceed the stringent requirements of various industries.
Contact Info
Main Office: Shakraka, Sulaymaniyah
Factory: Takiya, Sulaymaniyah
Email us:
info@sulikim.com
Call us now:
+964 (0)771 900 0006